Bumpers and Bullbars
FURY Front Bumper Jeep Wrangler JL / JLU 2018+ aluminium
FURY Awaken Series aluminium front bumper for the Jeep Wrangler JL. FURY states a product weight of 26 kg per piece, dimensions of 126.8 x 18.2 x 29.3 cm and a Samurai black finish. Six PDC parking sensors are inlaid into the bumper body, a skid plate is built in and the number plate sits on a pull-up rack. The structure is mechanically spliced and bolted, with no welding.
FURY Awaken Series Front Bumper for the Jeep Wrangler JL
The factory bumper on a JL looks fine in a car park, but off road it collects rocks and limits your approach angle. The FURY Awaken Series bumper is made from aluminium alloy and weighs 26 kg per piece — less than a steel equivalent, and that mass sits over the front axle, where the suspension feels it most.
FURY gives dimensions of 126.8 x 18.2 x 29.3 cm and a width matched to the front face of the vehicle. Six parking sensors are inlaid into the bumper body, a skid plate works underneath, and the number plate sits on a pull-up rack. The side wrap angles use a mechanical splicing structure with a linkage rod — the whole bumper is spliced and bolted, never welded.
Fitment Jeep Wrangler JL | Weight 26 kg / piece | PDC sensors 6, inlaid into the body |
Key benefits
- Six PDC sensors inlaid into the body — FURY describes them as integrated with the bumper surface, not dropped into generic holes.
- Skid plate included — it is part of the bumper, not a separate purchase.
- Pull-up number plate rack — the plate does not permanently block the lower section of the bumper.
- Bolt-together installation, no welding — FURY calls it non-destructive splicing installation, on mechanical joints.
- Aluminium, 26 kg per piece — a product weight stated by the manufacturer, not taken from a shipping field.
- Mechanically spliced wrap angles — the sides are assembled with a linkage rod and matched to the proportions of the factory wheel arches.
What is in the box
FURY does not publish a contents list — there is no information about bolts, brackets or an installation guide. All the manufacturer states is that the bumper is sold as a single piece.
Technical data
- Part number: TXFR FY003
- Brand: FURY, Awaken Series
- Fitment per manufacturer: Jeep Wrangler JL (no model years and no 2/4-door distinction given)
- Material: aluminium alloy
- Colour: Samurai black (FURY does not state the coating type)
- Product weight: 26 kg / piece
- Dimensions: 126.8 x 18.2 x 29.3 cm
- Parking sensors: 6, inlaid into the bumper body
- Skid plate: yes
- Number plate mount: pull-up rack
- Side wrap angles: mechanical splicing structure with a linkage rod
- Installation: non-destructive, spliced and bolted, no welding
- In the box: 1 pc
Who it is for
For JL owners who want to open up the front end and improve the approach angle without loading the front axle with a steel bumper. The six-sensor layout suits vehicles with factory PDC. If you are not sure which sensor configuration your Wrangler has, message us before ordering — we run an off-road workshop as well as the shop.
Installation and notes
FURY describes the installation as non-destructive, on mechanical joints and without welding, but does not state the number of mounting points, the contents of the fitting kit or whether drilling is needed. The manufacturer also says nothing at all about winch preparation or shackle mounts — if you need a winch-ready bumper, check with us first.
FURY does not state any type approval or road approval for this bumper. Replacing a front bumper is exactly the kind of change an inspector asks about, so we say it plainly: that declaration is not in the manufacturer's material. There is also no information about airbag or ADAS compatibility. The JL and JLU 2018+ fitment on our listing comes from the distributor — FURY states only the model Jeep Wrangler JL.
Why it is worth it
- Real weight and real dimensions from the manufacturer instead of a rounded shipping figure.
- Skid plate and pull-up plate rack as part of the bumper, not add-ons.
- Six inlaid sensors instead of a vague note about PDC cut-outs.
Frequently asked questions
How many parking sensors does this bumper take?
Six. FURY states the sensors are inlaid into the bumper body and integrated with its surface.
Is the bumper winch ready?
FURY gives no information at all about winch preparation, a winch plate or cradle, or shackle mounts. Until the manufacturer confirms it, do not assume this bumper is set up for a winch.
Does the bumper include a skid plate?
Yes. FURY states the bumper is equipped with a skid plate.
How much does the bumper weigh?
FURY states 26 kg per piece as the product weight. The declared shipping weight is 61 kg — that figure includes packaging.
Does the manufacturer state a type approval?
No. FURY gives no information about homologation, road approval or an E/ECE mark. We are not declaring it on their behalf.
